New Hot Cold Plates, Thermal Platforms

Thermal Platforms, Also Known as Hot/Cold Plates, are used to Conductively Heat and Cool Electronic Components under test. Our Thermal Platforms Precision Temperature Control and High Head Removal Rates lend themselves to remarkable effective Temperature Control – From Very Low to Very Hot. These Thermal Platforms perform the task of Heating or Cooling while maintaining temperatures quickly and precisely over a wide temperature range.

The incorporation of Hot/Cold Plates in your testing process can be an economic alternative to an actual Environmental Chamber if the product will have good surface contact. Get Fast High-Quality Testing Results at a Low Cost. See below for the wide selection of sizes and features of each unit.

Inventory of New Hot Cold Plates - Thermal Platforms

Category	Class	Stock No.	Manufacturer	Model No.
Hot Cold Plates	NH	T100	ESS HOT COLD PLATE / THERMAL PLATFORM	MRTP
Mechanically Refrigerated Thermal Platform Systems Model MRTP The MRTP thermal platform systems rely upon a closed loop mechanical refrigeration cooling system. This eliminates the need for expendable refrigerants such as liquid nitrogen and liquid carbon dioxide. Eliminating the non-reusable refrigerants also eliminates the purchasing cost and handling expenses, not to mention the associated icing and water condensation. The MRTP utilizes an efficient mechanical refrigeration system that re-circulates the refrigerant in a closed loop system. Only environmentally friendly zero-ozone depleting refrigerants are used. Proprietary design features provide fast ramp rates with efficient heat removal. The system is portable and a single AC outlet is all that is needed to operate it. The system normally uses an air-cooled condenser, which rejects a certain amount of heat into the room. If a water cooling source is available, the system can operate with a water-cooled condenser. If many systems will operate in the same room a water cooling circuit should be considered to remove the heat rejected by the refrigeration cycle. The MRTP utilizes an efficient mechanical refrigeration system that re-circulates the refrigerant in a closed loop system. Only environmentally friendly zero-ozone depleting refrigerants are used. Proprietary design features provide fast ramp rates with efficient heat removal. The system is portable and a single AC outlet is all that is needed to operate it. The system normally uses an air-cooled condenser, which rejects a certain amount of heat into the room. If a water cooling source is available, the system can operate with a water-cooled condenser. If many systems will operate in the same room a water cooling circuit should be considered to remove the heat rejected by the refrigeration cycle. There are two types of MRTP systems. The first type is called single stage and uses one refrigeration loop to cool the thermal platform. The second type called cascade uses two refrigeration loops in series enabling the temperature of the thermal plate to be as low as -80ºC.			Spec sheet:

Hot Cold Plates	NH	T700	ESS HOT COLD PLATE / THERMAL PLATFORM	T700
Hot Cold Plate / Thermal Platform Model #T700 SPECS: 6.75" X 6.75" OR 11" X 11" Plate Temperature Range: -99/65 to +200 Deg. C LN2 or LC02 Cooled 115/230V The T700-Series uses liquid nitrogen (LN2) or liquid carbon dioxide (LCO2) cooled thermal platforms. They utilize a premium integrated temperature controller similar to the T650 but with more standard features and offers a more traditional thermal plate form factor shape. The T700 series of thermal platform systems feature the PM6 temperature controller. The PM6 comes with everything you need for state of the art thermal plate control. The only option you may need is the GPIB-488 or the Ethernet/IP Modbus TCP remote interface. The PM6 comes standard with the following features: Large easy to read dual display showing both the current temperature and current set point Programmable ramp to set point Standard bus protocol EIA-485 serial communications for use with the free Configurator software interface program. Programmable ramp & soak profiling. Up to 4 profiles with a total of 40 steps Modbus RTU protocol EIA-232 serial communications Second sensor for monitoring the device under test (DUT) temperature Loomis-Logo-DnB_1 CONTROLLER OPTIONS: GPIB-488 communications interface Ethernet/IP Modbus TCP remote interface Standard bus is a proprietary protocol for use exclusively with the free Configurator software interface program To order a T700 thermal platform system you will need to choose either a 6-3/4" X 6-3/4" or 11" X 11" thermal plate size, 115 VAC or 230 VAC input facility power, LN2 or LCO2 cooling, an optional communications interface if desired and the destination country so we can include the correct power cord and plug. Stock #T700			Spec sheet:

Hot Cold Plates	NH	T650	ESS HOT COLD PLATE / THERMAL PLATFORM	T650
Hot Cold Plate / Thermal Platform Model T660 SPECS: 6.75" X 6.75" OR 11" X 11" Plate Temperature Range: -99/65 to +200 Deg. C LN2 or LC02 Cooled 115/230V The T650 Thermal Platforms are cooled using liquid nitrogen (LN2) or liquid carbon dioxide (LCO2) and utilize an integrated temperature controller. With the lowest initial cost, the T650 Thermal Platforms offer an excellent value. All stainless steel chassis and with a powerful integrated temperature controller. The T650 can be ordered with the standard or optional premium temperature controller. The standard controller has the following features: Large easy to read dual display showing both the current temperature and current set point Programmable ramp to set point Standard® bus protocol EIA-485 serial communications for use with the free Configurator software interface program The premium controller has the following additional features: Programmable ramp and soak profiling. Up to 4 profiles with a total of 40 steps Modbus RTU protocol EIA-232 serial communications Second sensor for monitoring the device under test (DUT) temperature To order a T650 thermal platform system you will need to choose either a 6-3/4" X 6-3/4" or 11" X 11" thermal plate size, 115 VAC or 230 VAC input facility power, LN2 or LCO2 cooling, The standard or premium controller and the destination country so we can include the correct power cord and plug. Stock #T650			Spec sheet:

Hot Cold Plates	NH	T600	ESS HOT COLD PLATE / THERMAL PLATFORM	T600
Hot Cold Plate / Thermal Platform Model T600 SPECS: 6.75" X 6.75" OR 11" X 11" Plate Temperature Range: -99/65 to +200 Deg. C 115/230V The T600 Thermal Platforms are cooled using liquid nitrogen (LN2) or liquid carbon dioxide (LCO2) and utilize a thermal plate with a separate temperature controller cabinet. They have the most standard, and optional features available of all the T-Series Thermal Platform Systems and offer the traditional form factor of a stand alone thermal plate with a remotely located temperature controller cabinet. Large easy to read dual display showing both the current temperature and current set point. Programmable ramp to set point Standard® bus protocol EIA-485 serial communications for use with the free Configurator software interface program Programmable ramp and soak profiling Up to 4 profiles with a total of 40 steps Modbus RTU protocol EIA-232 serial communications Second sensor for monitoring the device under test (DUT) temperature Stock #T600			Spec sheet:

New Test Equipment > Thermal Platforms

Hot Cold Plates, Thermal Platforms

New In Stock

T600

T650

T700

MRTP — Mechanically Refrigerated Thermal Platforms

Thermal Platform Options Available with Purchase of Units

Inventory of New Hot Cold Plates - Thermal Platforms